TCLT1600 Datasheet by Vishay Semiconductor Opto Division

VISHAY. m w @ ® RoH S comum "noes" FREE GREEN 5.2m- www.vishay.com/doc?99912 DDDDDDDD ogtocoug‘evanswersmwshay com www.v\shay.CUm/doc?91000

TCLT1600

www.vishay.com Vishay Semiconductors

Rev. 2.5, 13-Oct-15 1Document Number: 83517

For technical questions, contact: optocoupleranswers@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Optocoupler, Phototransistor Output, AC Input,

SOP-4L, Long Mini-Flat Package

DESCRIPTION

The TCLT1600 consists of a phototransistor optically

coupled to 2 gallium arsenide infrared-emitting diodes in an

SOP 4-pin wide body package.

AGENCY APPROVALS

• UL1577, file no. E76222

• CSA 22.2 bulletin 5A, double protection

• DIN EN 60747-5-2 (VDE 0884)/DIN EN 60747-5-5

(pending), available with option 1

• BSI IEC 60950; IEC 60065

FEATURTES

• Low profile package

• Extra low coupling capacity - typical 0.2 pF

• High common mode rejection

•AC input

• Creepage current resistance according to

VDE 0303/IEC 60112 comparative tracking

index: CTI ≥ 175

• Creepage distance > 8 mm

• Material categorization: for definitions of

compliance please see www.vishay.com/doc?99912

APPLICATIONS

• Switch-mode power supplies

• Line receiver

• Computer peripheral interface

• Microprocessor system interface

• Reinforced isolation provides circuit protection against

electrical shock (safety class II)

• Circuits for safe protective separation against electrical

shock according to safety class II (reinforced isolation):

- for appl. class I to IV at mains voltage ≤ 300 V

- for appl. class I to III at mains voltage ≤ 600 V

according to DIN EN 60747-5-2 (VDE 0884)

17295-5

ORDERING INFORMATIONS

TCLT1600

PART NUMBER

AGENCY CERTIFIED/PACKAGE CTR (%)

UL, cUL, VDE, BSI 80 to 300

SOP-4L, miniflat, long TCLT1600

10.2 mm

SOP-4L

VISHAY. www.mshaycom/GOC’WUUSA amocoup‘evanswerséiwshay com www.v\shay.com/doc?91000

TCLT1600

www.vishay.com Vishay Semiconductors

Rev. 2.5, 13-Oct-15 2Document Number: 83517

For technical questions, contact: optocoupleranswers@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Notes

• Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not

implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute

maximum ratings for extended periods of the time can adversely affect reliability.

(1) Wave soldering three cycles are allowed. Also refer to “Assembly Instruction” (www.vishay.com/doc?80054).

Note

• Minimum and maximum values are tested requierements. Typical values are characteristics of the device and are the result of engineering

evaluations. Typical values are for information only and are not part of the testing requirements.

ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified)

PARAMETER TEST CONDITION SYMBOL VALUE UNIT

INPUT

Forward current IF± 60 mA

Forward surge current tp ≤ 10 μs IFSM ± 1.5 A

Power dissipation Pdiss 100 mW

Junction temperature Tj125 °C

OUTPUT

Collector emitter voltage VCEO 70 V

Emitter collector voltage VECO 7V

Collector current IC50 mA

Collector peak current tp/T = 0.5, tp ≤ 10 ms ICM 100 mA

Power dissipation Pdiss 150 mW

Junction temperature Tj125 °C

COUPLER

Total power dissipation Ptot 250 mW

Operating ambient temperature range Tamb -55 to +100 °C

Storage temperature range Tstg -55 to +125 °C

Soldering temperature (1) Tsld 260 °C

ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT

INPUT

Forward voltage IF = ± 50 mA VF- 1.25 1.6 V

Junction capacitance VR = 0 V, f = 1 MHz Cj-50-pF

OUTPUT

Collector emitter voltage IC = 1 mA VCEO 70 - - V

Emitter collector voltage IE = 100 μA VECO 7--V

Collector ermitter leakage current VCE = 20 V, IF = 0 A ICEO - 10 100 nA

COUPLER

Collector emitter saturation voltage IF = ± 10 mA, IC = 1 mA VCEsat --0.3V

Cut-off frequency VCE = 5 V, IF = ± 10 mA,

RL = 100 Ωfc- 110 - kHz

Coupling capacitance f = 1 MHz Ck-0.3-pF

CURRENT TRANSFER RATIO (Tamb = 25 °C, unless otherwise specified)

PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT

IC/IFVCE = 5 V, IF = ± 5 mA CTR 80 - 300 %

VISHAY. Pmmuanssm Pso WW} \R-dmne ‘sx (M) agtocoup‘evanswersmwshay com www.v\shay,com/doc?91000

TCLT1600

www.vishay.com Vishay Semiconductors

Rev. 2.5, 13-Oct-15 3Document Number: 83517

For technical questions, contact: optocoupleranswers@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

• According to DIN EN 60747-5-2 (VDE 0884) (see figure 2). This optocoupler is suitable for safe electrical isolation only within the safety

ratings. Compliance with the safety ratings shall be ensured by means of suitable protective circuits.

Fig. 1 - Derating Diagram Fig. 2 - Test Pulse Diagram for Sample Test according to

DIN EN 60747-5-2; IEC60747-5-5

SAFETY AND INSULATION RATINGS

PARAMETER TEST CONDITION SYMBOL VALUE UNIT

Partial discharge test voltage - routine test 100 %, ttest = 1 s Vpd 2kV

Partial discharge test voltage -

lot test (sample test)

tTr = 60 s, ttest = 10 s,

(see figure 2)

VIOTM 8kV

Vpd 1.68 kV

Isolation test voltage (RMS) VISO 5000 VRMS

Insulation resistance

VIO = 500 V RIO 1012 Ω

VIO = 500 V, Tamb = 100 °C RIO 1011 Ω

VIO = 500 V, Tamb = 150 °C

(construction test only) RIO 109Ω

Forward current Isi 130 mA

Power dissipation PSO 265 mW

Rated impulse voltage VIOTM 8kV

Safety temperature Tsi 150 °C

Clearance distance 8.00 mm

Creepage distance 8.00 mm

Insulation distance (internal) 0.40 mm

0 25 50 75 125

100

150

200

300

TSI - Safety Temperature (°C)

150

100

250 Phototransistor

PSO (mW)

IR-diode

ISI (mA)

13930

, t2 = 1 s to 10 s

t3, t4 = 1 s

ttest = 10 s

tstres = 12 s

VIOTM

Vpd

VIOWM

VIORM

ttest

tTr = 60 s tstres

t3t4

SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT

Delay time VS = 5 V, IC = 2 mA, RL = 100 Ω,

(see figure 3) td-3 -μs

Rise time VS = 5 V, IC = 2 mA, RL = 100 Ω,

(see figure 3) tr-3 -μs

Turn-on time VS = 5 V, IC = 2 mA, RL = 100 Ω,

(see figure 3) ton -6 -μs

Storage time VS = 5 V, IC = 2 mA, RL = 100 Ω,

(see figure 3) ts-0.3 -μs

Fall time VS = 5 V, IC = 2 mA, RL = 100 Ω,

(see figure 3) tf-4.7 -μs

Turn-off time VS = 5 V, IC = 2 mA, RL = 100 Ω,

(see figure 3) toff -5 -μs

Turn-on time VS = 5 V, IF = 10 mA, RL = 1 kΩ,

(see figure 4) ton -9 -μs

Turn-off time VS = 5 V, IF = 10 mA, RL = 1 kΩ,

(see figure 4) toff -10 -μs

H /’\ H M r’ 7" ’1 I I ISZ: | 7 | I L- ___ -4 $$I T agtocougIevanswersmIshay com www.VIshay.com/uoc?91000

TCLT1600

www.vishay.com Vishay Semiconductors

Rev. 2.5, 13-Oct-15 4Document Number: 83517

For technical questions, contact: optocoupleranswers@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Fig. 3 - Test Circuit, Non-Saturated Operation

Fig. 4 - Test Circuit, Saturated Operation

Fig. 5 - Switching Times

Channel I

Channel II

95 10804

RG = 50 Ω

tp = 50 µs

T= 0.01

+ 5 V

50 Ω100 Ω

IC = 2 mA; adjusted through

input amplitude

Oscilloscope

RL= 1 MΩ

CL= 20 pF

Channel I

Channel II

95 10843

RG= 50 Ω

tp= 50 µs

T= 0.01

+ 5 V

50 Ω1 kΩ

IF= 10 mA

Oscilloscope

≥

CL20 pF

1 MΩ

≤

tpt

10 %

90 %

100 %

ton

tstf

toff

tpPulse duration

tdDelay time

trRise time

ton (= td + tr) Turn-on time

tsStorage time

tfFall time

toff (= ts + tf) Turn-off time

96 11698

— V VISHAY. @ ‘E a\

TCLT1600

www.vishay.com Vishay Semiconductors

Rev. 2.5, 13-Oct-15 5Document Number: 83517

For technical questions, contact: optocoupleranswers@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

PACKAGE DIMENSIONS (in millimeters)

PACKAGE MARKING

TAPE AND REEL DIMENSIONS (in millimeters)

Fig. 6 - Reel Dimensions (3000 units per reel) Fig. 7 - Tape Dimensions

22533

7.50 ± 0.20

Seating plane

0.70 + 0.30

- 0.40

technical drawings

according to DIN

specifications

8.20

10.80

Possible footprint

2.54

0.90

4.10 max.

3.80

2.00

2.30 max.

2.54 nom.

Pin no. 1 identification

0.45 ± 0.1

+ 0.30

- 0.40

10.20

0.20 + 0.10

- 0.05

0.10

TCLT1600

V YWW 68

ESD sticker

Tape slot

in core

330

(13")

Regular, special

or bar code label

17999

22662

technical drawings

according to DIN

specification

4.25 8

2.3

2.7

0.3

7.5

10.6

Ø 1.55

1.75

Ø 1.6

5°

Direction of pulling out

VISHAY. max zen ogtocoug‘evanswersmwshay com www.v\shay.com/doc?91000

TCLT1600

www.vishay.com Vishay Semiconductors

Rev. 2.5, 13-Oct-15 6Document Number: 83517

For technical questions, contact: optocoupleranswers@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

SOLDER PROFILE

Fig. 8 - Lead (Pb)-free Reflow Solder Profile

according to J-STD-020

HANDLING AND STORAGE CONDITIONS

ESD level: HBM class 2

Floor life: unlimited

Conditions: Tamb < 30 °C, RH < 85 %

Moisture sensitivity level 1, according to J-STD-020

100

150

200

250

300

0 50 100 150 200 250 300

Time (s)

Temperature (°C)

240 °C 245 °C

max. 260 °C

max. 120 s max. 100 s

217 °C

max. 30 s

max. ramp up 3 °C/s

max. ramp down 6 °C/s

19841

255 °C

— VISHAY. V

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 01-Jan-2021 1Document Number: 91000

Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of

typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding

statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a

particular product with the properties described in the product specification is suitable for use in a particular application.

Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over

time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.

Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for

such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document

or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Products related to this Datasheet

OPTOISOLATR 5KV TRANSISTOR 4-SOP

TCLT1600

OPTOISOLATR 5KV TRANSISTOR 4-SOP

TCLT1600

OPTOISOLATR 5KV TRANSISTOR 4-SOP

TCLT1600